Highlander® HL-2C. salt and sand spreaders to control snow and ice, vacuum leaf loaders machines, tire recycling machines, all season dump bodies, v-box spreaders, and other municipal equipment manufactured by Loughberry Mfg. Corp. under the Tarco brand.
Highlander® HL-2C. salt and sand spreaders to control snow and ice, vacuum leaf loaders machines, tire recycling machines, all season dump bodies, v-box spreaders, and other municipal equipment manufactured by Loughberry Mfg. Corp. under the Tarco brand.






E-mail: info@loughberry.com
www.loughberry.com
Highlander® HL-2C. salt and sand spreaders to control snow and ice, vacuum leaf loaders machines, tire recycling machines, all season dump bodies, v-box spreaders, and other municipal equipment manufactured by Loughberry Mfg. Corp. under the Tarco brand.
Highlander® HL-2C. salt and sand spreaders to control snow and ice, vacuum leaf loaders machines, tire recycling machines, all season dump bodies, v-box spreaders, and other municipal equipment manufactured by Loughberry Mfg. Corp. under the Tarco brand.
HIGHLANDER®
HL-2C

Highlander® HL-2C. salt and sand spreaders to control snow and ice, vacuum leaf loaders machines, tire recycling machines, all season dump bodies, v-box spreaders, and other municipal equipment manufactured by Loughberry Mfg. Corp. under the Tarco brand.

Highlander® HL-2C. salt and sand spreaders to control snow and ice, vacuum leaf loaders machines, tire recycling machines, all season dump bodies, v-box spreaders, and other municipal equipment manufactured by Loughberry Mfg. Corp. under the Tarco brand.

Highlander® HL-2C. salt and sand spreaders to control snow and ice, vacuum leaf loaders machines, tire recycling machines, all season dump bodies, v-box spreaders, and other municipal equipment manufactured by Loughberry Mfg. Corp. under the Tarco brand.

SPECIFICATIONS

HOPPER LENGTH
LEVEL CAP. (YDS)
WIDTH
HEIGHT
LENGTH O.A. (approx)
LEVEL CAPACITY W/HOPPER EXTENSIONS
2"
4"
6"
8"
10"
12"
8' 5.0 83" 42" 10' 5.2 5.5 5.9 6.2 6.5 6.9
9' 5.5 83" 42' 11' 5.9 6.2 6.6 7.0 7.4 7.7
10' 6.1 83" 42" 12' 6.5 6.9 7.3 7.7 8.2 8.5
11' 6.8 83" 42" 13' 7.3 7.7 8.0 8.6 9.1 9.4
12' 7.3 83" 42" 14' 7.9 8.4 8.7 9.4 9.9 10.2

Other sizes and dimensions are available upon request.
NOTE:  To find the load any model will carry, use these approximate material weights:
    1 cu yd dry salt = 2,200 lbs.
    1 cu yd wet sand = 3,300 lbs.


HOPPER BODY:  Constructed of 10 ga. electrically welded steel; one-piece side, end and middle sheets; 7 ga, corten or stainless steel available; front and rear positioning and restraining members included; sides sloped at 45 degrees and channel formed to provide a rigid rail; four lifting eyes provided; standard unit 42" high by 83" wide.

CONVEYOR ASSEMBLY:  Material conveyed from hopper to distributor disc by two 24" conveyors; conveyor chains have tensile strength of 42,000 lbs. each, and barrel diameter of 7/8" with stainless steel disconnects; conveyors operate on 3/16" thick abrasion resistant wear plates; wear plates mounted on tracks for replacement; conveyor chain wipers at front and rear;  chain protected by 10 gauge steel aprons;  unit includes two crank actuated discharge gates each with discharge area up to 240 square inches;  lower edge of gate fitted with flexible seal;  spring cushioned conveyor idlers are self compensating and adjustable for tension over a 4" range;  ball bearings are relubricable, and idler adjustment is located at the rear of hopper.

HYDRAULICALLY POWERED CONVEYOR:  Conveyor drive shaft speed range .5 to 40 RPM;  RPM/GPM factor of 1.5;  maximum pressure rating of 3,000 psi;  overall efficiency of 95% at 3,000 psi;  constant torque regardless of RPM of not less than 30,000 inch pounds at 1,500 psi;  delivers 14 to 5,500 pounds per minute of rock salt at conveyor drive shaft speed of 1/4 to 40 RPM;  a 2" diameter conveyor drive shaft fitted with two 8-tooth drive sprockets per conveyor.

DISTRIBUTOR DISC:  10 gauge steel 20" diameter with six replaceable abrasion resistant vanes;  driven by direct coupled hydraulic motor; disc may be moved horizontally to provide desired spread pattern to the right, left or directly behind spreader;  four deflectors regulate the spread pattern from 8 to 40 feet;  deflectors and disc may be adjusted 16 inches vertically;  disc and chute assembly can be removed for stock piling or ground storage.

OPTIONS: •Top Screens  •Directional Signals   •Flasher Lights  •Tailgate Locks  •Cab Controls - Variable Speed Cab Control, Electrically Actuated Control Valve, and Ground Speed Control   •Spread Apron  •Dual Spinners  •Hold Down Equipment   •Conveyor Bridge  •Hopper Extensions  •Front Mounted Spinners  •Hoist-It-Legs   •Special Paint and Epoxy
Phone: (518) 584-4400
FAX: (518) 584-6630